How Many Tie-Downs a Load Needs and How to Count Them

How many tie-downs does a load need? Count by length and by working load limit, check both rules, and learn why experienced flatbed drivers add more.

How many tie-downs do you need for a load? Two checks decide it, and the load must pass both. The first counts tie-downs by the length of the cargo. The second adds up the working load limit of every tie-down and compares it with the weight of the cargo. Whichever rule asks for more wins. This page shows how to run both counts, why experienced drivers add extra, and where to find the actual numbers for your country.

The exact numbers come from the securement rules where you work and from your employer's procedure. We do not give a number here, because it changes between places and by type of cargo. We give the method. It sits inside our wider load securement guide for truck drivers.

Two rules, both must pass

Think of securement as two separate questions.

  1. Is the cargo held in enough places? This is the count by length. Long cargo needs tie-downs spread along it, so no end can lift, swing or slide.
  2. Is the total strength enough? This is the count by working load limit. The tie-downs together must be strong enough to hold the weight when the truck brakes, turns or hits a bump.

A load can pass one and fail the other. A long, light stack may have enough tie-downs by length but too little strength. A short, heavy block may have enough strength by rating but not enough places to hold it. You need to check both, every time.

Counting by length

The rule sets a minimum number of tie-downs for a length of cargo, and often a minimum of one or two for small items. It also asks for tie-downs near the ends, so the ends cannot move. The details depend on whether the cargo is in one piece, or in several pieces that can move separately.

A practical way to count:

  1. Measure or estimate the length of the cargo in one piece.
  2. Find the number your rule gives for that length. Write it down.
  3. Place one tie-down near the front and one near the rear, close to the ends, then space the rest evenly between them.
  4. If the load is made of separate pieces (bundles, pipes, logs), check each piece or each stack, not only the whole load.

Mark where each tie-down sits in your mind. A tie-down that crosses the cargo at an angle or under an edge may count for less, so check how your rule treats it.

Counting by working load limit

Every strap, chain, binder and hook has a working load limit. It is the most load the manufacturer says the piece can carry in normal use. It is printed or stamped on a tag or on the hardware. A strap with an unreadable tag should not be used, because you cannot know its rating.

The rule asks that the sum of the working load limits of all tie-downs be at least a stated fraction of the cargo weight. A tie-down that goes over the cargo and is fixed on both sides is counted in a particular way. A tie-down that is fixed at one end only, or that is used as a loop, may count differently. Read the rule where you work or ask your safety lead how to count each type.

Here is the method:

  1. Find the weight of the cargo on the paper, or estimate it from the item rating. Do not guess low.
  2. Find the fraction your rule requires of that weight.
  3. Read the working load limit on each tie-down and add them up as your rule counts them.
  4. Compare the total with the number from step 2. If it is lower, add tie-downs or use stronger ones.

Remember that the weakest part of the chain sets the strength. A strong strap on a weak anchor point is only as strong as the anchor point. Our guide to tarping a flatbed load safely also covers how tarps and tie-downs work together.

Why experienced drivers add more

The rules give a minimum. Experienced drivers rarely stop at the minimum, because the minimum assumes everything is perfect.

  • Straps wear. Old straps lose strength even if they look fine.
  • Loads settle. A stack compresses on the road, and straps get slack.
  • Edges cut. Sharp corners cut straps if edge protectors are missing.
  • Roads are rough. A hard brake or a pothole puts far more force on the tie-downs than a smooth road does.
  • Mistakes happen. A tie-down can be placed badly or not pulled tight enough.

An extra strap costs a few minutes and a small amount of money. A load that shifts or falls can hurt other road users and destroys the freight. Many drivers add one or two beyond the minimum on every load as a habit. Follow your employer's policy, which may require more than the rule.

Always recheck the tie-downs soon after you start and at every stop. Straps loosen. This is part of the pre-trip and en-route routine, as in our truck pre-trip inspection guide.

Example: a stack of lumber that passed one rule and failed the other

Say a flatbed driver, Lukasz, loads a stack of lumber that is long and moderately heavy. The rule for his area, as his safety lead explains it, needs a certain number of tie-downs for the length of the stack. Lukasz counts, and he has placed that number: one near each end and the rest spread between.

He thinks he is done. Then he follows the second check. He reads the tags. Several of his straps are the lighter type, with a lower working load limit than his heavy straps. He adds up the ratings the way his rule counts them. The total is below the required fraction of the cargo weight.

The first rule passed. The second failed. Lukasz swaps four of the light straps for heavier ones and adds one more across the middle, so the total now passes. He also puts edge protectors under the straps at the corners of the stack, so the sharp edge does not cut them. At the first stop, after a few miles, he rechecks and tightens two straps that have loosened.

Without the second check, the load would have looked fine and may have moved on the first hard stop.

When this does not work

  • Unusual cargo, such as machinery, pipes, coils, logs or vehicles, has its own rules and its own blocking and bracing methods. Do not use the general count for these. Ask your employer for the method.
  • Damaged or unmarked tie-downs cannot be counted. Take them out of service.
  • A very short or very light item may follow a different minimum. Check your rule.
  • If you are not sure whether the load is secure, do not drive. Ask a supervisor or a trained person. Do not rely on a guess.

If you work on a closed trailer, a dry van, load bars and straps do the same job there, as in our guide to using load bars in a dry van.

Learn this in five minutes

The Tie-Down Fundamentals track in CargoSkills teaches why cargo moves, how to choose straps, chains and binders, how to calculate the number of tie-downs, how to use edge protectors and blocking, and how to recheck securement in the first miles. Each lesson takes about five minutes.

All articles